Tube laser cutting / Design guide

Design guide · Vernon, NJ

Tube laser cutting design guide

These are the rules our tube laser works to, and the same ones our online quoting checks when you upload a part. Follow them and your part quotes faster, cuts cleaner and fits at the welding table. Where we do not have a number yet, this guide says ask us.

Quick reference

The numbers in one place

Largest square tube7.75″ × 7.75″
Largest round tube and pipe7.75″ outside diameter
Largest channel6″
Rectangular tube and angleSend the size and we confirm fit
Stick lengths20 ft and 24 ft
Longest part229″ from a 20 ft stick, 277″ from a 24 ft stick
Smallest holeAs wide as the wall is thick
End cutsUp to 45° as modeled. Steeper cuts are checked by hand
FileSTEP (.step or .stp), up to 25 MB
Typical tolerance±0.010″ on holes, slots and length up to 48″. ±0.020″ on length over 48″
Slot clearance and weld prepAsk us. We confirm these for each job

Start from a real tube size

Square and round up to 7.75″. Channel up to 6″.

Design around tube you can buy. Model the outside size and the wall of a standard mill size, and tell us the material: A500 or A513 steel, 304 stainless, or 6061 or 6063 aluminum.

Our tube laser takes square tube up to 7.75″ × 7.75″, round tube and pipe up to 7.75″ outside diameter, and channel up to 6″. For rectangular tube and angle, send the size and we confirm it fits when we quote.

If your file is drawn at one wall and you order a different wall, we cut the wall you ordered. Check that your holes and joints still work at that wall before you send it.

Model the rounded corners

Holes and slots sit on the flats, clear of the corner radius.

Square and rectangular tube is not sharp at the corners. The mill forms each corner to a radius, and a heavier wall has a larger one. Model that radius. A STEP drawn with sharp corners does not match the tube on the machine.

Keep holes and slots on the flat faces, clear of the corners. A feature that runs into the corner is cut on a curved surface. It comes out a different shape than the model, and it weakens the corner.

tube seen from the end
GoodThe hole sits on the flat face.
tube seen from the end
PoorThe hole runs into the rounded corner.

Size holes to the wall

Hole width is at least the wall thickness.

Keep every hole at least as wide as the wall is thick. On a 0.120″ wall, the smallest hole is 0.120″. If you need a smaller one, tell us and we quote another way to make it.

Model a hole through both walls when you want it through both walls. A hole drawn in one wall is cut in one wall.

For slot width, and for the distance from a hole to the end of the tube, we have not published a number yet. Send the part and we check it when we quote.

holewallwall seen in section
GoodThe hole is wider than the wall is thick.
holewallwall seen in section
PoorThe hole is narrower than the wall.

End cuts, miters and copes

Up to 45° cuts as modeled. Past 45° we check it by hand.

Square ends and miters up to 45 degrees are cut as modeled. Past 45 degrees we check the cut by hand before we price it, so those parts take a little longer to quote.

For a cope, where one tube saddles onto another, model the real intersection of the two tubes and leave it in the STEP. The laser follows the shape in the file, so the joint fits the way the model fits.

On a mitered frame, model each tube at its true cut length. Then nothing has to be worked out from a drawing.

45°tube seen from the side
GoodA 45 degree miter cuts as modeled.
60°tube seen from the side
Checked by handPast 45 degrees we check the cut before we quote.

Tab and slot frames

Tell us the fit you want. We set the clearance with you.

Tabs and slots let tubes and plates locate each other before the first weld. The frame squares itself and the fixtures get simpler.

Leave clearance so the parts go together by hand. How much depends on the wall, the material and the finish, and we have not published one number that fits every tube. Tell us how tight you want the fit and we set it with you on the first parts.

Put tabs and slots on the flat faces, for the same reason as holes.

Part length and the stick

Longest part: 229″ (20 ft stick) or 277″ (24 ft stick).

Tube comes in 20 ft and 24 ft sticks. The machine holds the last 10 inches of each stick in the chuck and trims 1 inch off the end. So the longest single part is 229″ from a 20 ft stick and 277″ from a 24 ft stick.

Shorter parts nest end to end along the stick. When your parts add up to just under a full stick, less of it becomes drop.

A part longer than the stick can be split into two pieces with a joint. Or send it as it is and our office quotes another way to make it.

1″ trim10″ in the chuckparts nest end to end229″ on a 20 ft stick, 277″ on a 24 ft stick
Each stick gives up 11 inches: 10 in the chuck and 1 at the end. Not to scale.

Tolerances

Typical: ±0.010″ on holes, slots and length up to 48″.

Hole and slot size±0.010″
Cut length, parts up to 48″±0.010″
Cut length, parts over 48″±0.020″

These are the typical tolerances on laser cut tube. If a dimension needs to be tighter, tell us which one and we confirm what we hold when we quote.

Long parts get the wider length tolerance because metal grows as it warms during cutting. A 10 ft steel part that warms 20°F grows about 0.016″.

The tube itself varies more than the cut. On A500 structural tube the mill is allowed a wall 10 percent over or under nominal and a corner radius up to 3 times the wall, and every stick has some twist and bow. So a hole can be exactly where the laser put it and still sit off from the opposite face.

Dimension the features that matter from one face and one end of the tube, not across it.

Weld prep and fit up

Call out gaps and bevels. We confirm them when we quote.

Show where the welds go. A note or a weld symbol on a drawing is enough.

If you want a root gap or a bevel, model it or call it out. We do not have a published weld prep table for tube yet, so we confirm it with you when we quote.

If we are welding the frame too, send the whole assembly. We check that every member fits the machine and that each joint can be reached to weld.

Set up the STEP file

One solid body for each tube, saved as STEP, under 25 MB.

Send a STEP file, .step or .stp, up to 25 MB. A STEP carries every cope, hole and slot in three dimensions, so we program from your model and nothing is redrawn.

Model each tube as one solid body with its real outside size, wall and corner radius.

Units come from the file, so there is nothing to pick. After you upload, check that the length reads the way you expect.

For a frame, upload the whole assembly as one STEP. A DXF is for flat sheet parts. A tube needs a STEP.

Before you upload

Tube part checklist

  • The tube is a standard size, within 7.75″ square or round, or 6″ channel
  • The corners are modeled with their radius
  • Every hole is at least as wide as the wall, and on a flat face
  • End cuts are 45 degrees or less, or you expect a hand check
  • No part is longer than 229″ (20 ft stick) or 277″ (24 ft stick)
  • Each tube is one solid body, saved as STEP, under 25 MB
  • You know the material, the wall and the quantity
Common questions

Tube design FAQ

What is the smallest hole you can laser cut in tube?

A hole at least as wide as the wall is thick. On a 0.120″ wall that is a 0.120″ hole. Keep holes on the flat faces of square and rectangular tube, clear of the corners.

How long can a tube laser part be?

229″ from a 20 ft stick and 277″ from a 24 ft stick. The machine holds 10 inches of each stick in the chuck and trims 1 inch off the end.

Can you cut a miter steeper than 45 degrees?

Often, yes. Cuts up to 45 degrees are made as modeled. Past 45 degrees we check the cut by hand before we quote, so send the file and we tell you.

What file do I need for tube laser cutting?

A STEP file, .step or .stp, up to 25 MB, with each tube modeled as one solid body at its real size, wall and corner radius. A DXF is for flat sheet parts.

What tolerance do you hold on laser cut tube?

Typically ±0.010″ on hole and slot size and on cut length up to 48″, and ±0.020″ on cut length over 48″. The tube itself varies more than the cut, so tell us which dimensions matter and we confirm what we hold when we quote.

Where do I upload a tube part?

At parts.teomfg.com. Make a free account, add your STEP file, and follow your quote there. Quotes come back within 1 business day.

Ready to cut

Upload a STEP. Get a quote within 1 business day.

Not sure a part follows the guide? Send it anyway. We open every file, and if something will cut poorly or cost more than it should, we tell you before we quote.