Tube & structural laser · Vernon, NJ

Tube laser cutting

Round, square and rectangular tube, pipe, angle and channel cut on a 3 kW fiber tube laser in Vernon, NJ. Copes, miters, holes, slots and weld prep come off the machine in one pass, ready to bend or weld. Send a STEP file and get a quote within 1 business day.

At a glance
  • 3 kW fiber tube laser, 300″ feed
  • Full 24 ft sticks
  • 7.75″ square and round tube, 6″ channel
  • Copes, holes, slots and weld prep in one pass
  • Quote within 1 business day
Specifications

What the tube laser takes

Machine3 kW fiber tube laser with a 300 inch feed
Stick lengthFull 24 ft sticks, loaded whole
ShapesRound tube, square tube, rectangular tube, pipe, angle and channel
Largest square tube7.75″ × 7.75″
Largest round tube and pipe7.75″ outside diameter
Largest channel6″
Rectangular tube and angleSend the size and we confirm fit when we quote
MaterialsMild steel (A500 and A513 tube), stainless steel, aluminum (6061 and 6063)
What the laser cutsCopes, miters, holes, slots, tab and slot joints, weld prep
QuantitiesOne prototype to full production runs, no minimum
Quote turnaroundWithin 1 business day
How it works

Three steps from file to finished parts

  1. 1

    Upload a STEP

    Send a STEP file of the tube or the whole frame. Add the material, wall thickness, quantity and the date you need it. A dimensioned PDF helps when you have one.

  2. 2

    We check it and quote

    We open the model, confirm the profile fits the machine, flag anything that will cut poorly or cost more than it should, and send a price within 1 business day.

  3. 3

    We cut and ship

    Parts are programmed from your file, cut from full sticks, labeled and packed. Our own truck delivers within about 80 miles of Vernon, and everything else ships by UPS or freight.

What a tube laser does that a saw cannot

A band saw cuts tube to length. Everything after that, the notch where two tubes meet, the bolt holes, the slot for a gusset, gets laid out by hand and cut on a drill press, a hole saw or a notcher. Each of those steps adds handling time and a chance for error, and the errors show up later at the welding table as gaps that need filler or grinding.

A tube laser does all of it in one pass. The tube is loaded as a full stick, and the machine cuts every feature in the part, then the part's length, then moves on to the next part on the same stick. A coped joint lands exactly where the model put it, a hole sits the same distance from the end on part one and part five hundred, and the finished pieces come off the machine ready to fit.

For anyone building frames, carts, racks, railings, guards, furniture bases or machine weldments, that changes the job. Fit up is faster, welds are more consistent, and the assembly matches the drawing without a fitter adjusting every joint.

Copes, miters, holes, slots and tab and slot joints

Copes and fishmouth joints let one tube meet another at any angle with a tight, even gap for welding. The laser cuts the saddle shape from the model, so a 90 degree tee, a 45 degree brace or a compound angle all fit the same way.

Miters join two tubes at a corner. Cut on a laser, the two faces meet flush, which matters on visible work like railings and furniture where a gap would show after finishing.

Holes and slots are cut through one or both walls with their position held from the end of the tube, so bolt patterns line up across a whole run. Slots can take gussets, brackets or sheet metal tabs.

Tab and slot joints let tubes and plates locate each other before a weld is laid. Parts click together in the right place, which cuts down on fixtures and keeps square frames square. Weld prep, such as a bevel or relief on the joint, is added at the same time so the weld can go in without grinding first.

Designing tube parts for the laser

Model the tube as a solid body with the real outside size and wall thickness, and export it as a STEP. A STEP carries every cope, hole and slot in three dimensions, so we can program it directly instead of redrawing it from a print.

Tell us the material specification. A500 structural tube, A513 mechanical tubing, 304 stainless and 6061 or 6063 aluminum all cut well, and knowing which one you need lets us quote stock we have or source the right grade.

Leave a little clearance in slots and tab and slot joints so parts assemble without forcing. If two parts must be oriented the same way, ask us to add a small etched mark or a locating notch. If the finished part will be bent, send the bent shape and tell us where the bends go, and we will cut the flat stick so the holes land in the right place after bending.

When the design is a full frame, send the whole assembly. We can check that every member fits the machine, nest the parts across full sticks to cut down on drop, and flag any joint that would be easier and cheaper to make another way.

From prototype to production on the same machine

There is no minimum order. A single prototype is programmed and cut the same way as a production run, so once a part is approved, the run that follows matches the sample exactly.

On production work, parts are nested across full 24 ft sticks to use as much of each stick as possible. That keeps material cost down, and it is one of the main reasons a tube laser price often beats a saw and drill price on repeat parts.

Heavier sections that go beyond the laser's size run on our CNC plasma tube cutter in the same building, so a frame that mixes light tube and heavy structural members can still come from one shop.

After the cut: bending, welding and finishing in one shop

Most tube parts need more than a cut. Our CNC tube bender puts accurate radii into the same sticks the laser cut, so holes and copes land where they belong after the bend. Welding runs by hand on MIG and TIG stations and in a 7 axis robotic cell for repeat frames, on fixture tables that keep weldments square.

Paint, zinc coating and clear coat are done in house. Powder coating and anodizing go through finishing partners we manage. One quote and one shop from a raw stick of tube to a finished, welded assembly.

Delivered across New Jersey and New York City, shipped nationwide

The shop is in Vernon, New Jersey. Our own truck delivers within about 80 miles: North and Central New Jersey, all five boroughs of New York City, Westchester, Rockland, the Hudson Valley, northeast Pennsylvania and southwestern Connecticut. Smaller orders ship by UPS and usually arrive the next business day. Larger orders go by freight anywhere in the United States, and pickup at the shop is welcome.

From the floor

Tube laser work in Vernon, NJ

Common questions

Tube laser cutting FAQ

What is the largest tube you can laser cut?

Square tube up to 7.75″ × 7.75″, round tube and pipe up to 7.75″ outside diameter, and channel up to 6″. The machine takes full 24 ft sticks on a 300 inch feed. For rectangular tube and angle, send the size and we confirm it when we quote.

What materials can you cut on the tube laser?

Mild steel, including A500 structural tube and A513 mechanical tubing, stainless steel, and aluminum in 6061 and 6063. Tell us the specification and we quote from stock or source the grade.

How fast can I get a quote?

Within 1 business day. Send a STEP file with the material, wall thickness and quantity. If something in the model will cut poorly or cost more than it should, we tell you before we quote.

What file should I send?

A STEP file is best because it carries every cope, hole and slot in three dimensions. A dimensioned PDF helps as a second reference. If you only have a sketch, send it with dimensions and we can model the part.

Is there a minimum order?

No. One prototype or a full production run, programmed and cut the same way.

Can you bend and weld the tube after cutting?

Yes. The same shop bends tube on a CNC tube bender and welds by hand and in a 7 axis robotic cell. Paint, zinc coating and clear coat are done in house, and powder coating goes through finishing partners we manage.

Do you deliver tube laser parts to New York City?

Yes. Our own truck covers about 80 miles from Vernon, NJ, including all five boroughs. Smaller orders ship by UPS and larger ones by freight anywhere in the United States.

Can I upload files online?

Yes. Upload your part at parts.teomfg.com: make a free account, add your STEP file, and follow your quote there. Quotes come back within 1 business day.

Send us your tube file

Attach a STEP. Get a quote within 1 business day.

Add the material, wall thickness, quantity and the date you need the parts. No minimum order. You can also upload your part online and follow your quote there.